Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 


Reply
 
Thread Tools Display Modes
 
Old 10-31-2016, 01:38 PM   #1
Senior Member
 
Join Date: Aug 2011
Posts: 261
Rear differential seal?

Im looking to find a write up on how to and maybe tools needed to replace the rear differential seal. This isnt the big pumpkin seal but the other end where the drive shaft hooks into the differential. Can anyone point me in the correct direction for the proper info on this repair? Ive got a small drip going on, funny, all Ive been doing lately is replacing seals. When one goes they all seem to go in the drive line. LOL. This is for a 2005 E-350 6.0
Thank you!
Tracey

__________________
2005 Ford E-350 SMB 4x4
6.0 EB 50 floor plan. sold :(
TraceyAZ is offline   Reply With Quote
Old 10-31-2016, 01:57 PM   #2
Senior Member
 
Join Date: Jul 2011
Location: Flagstaff, AZ
Posts: 1,995
Full float or semi-float? It's probably a Dana60 but could be a dynatrac? Anyhow, to be sure find the BOM #. http://differentials.com/wp-content/.../EB_AxleID.jpg

Then, you can use this link to find the part's schematic for your axle: Dana Holding Corporation - The Expert Axle Bill of Material

Another handy link: Axle Builder | Dana 60 Axle Parts and Upgrades
__________________
2005 E350 RB 6.0 PSD for extended fun
1989 Landcruiser FJ62 for local fun
2011 VW TDI Golf for hwy fun
JoeH is offline   Reply With Quote
Old 10-31-2016, 01:59 PM   #3
Senior Member
 
Join Date: Aug 2011
Posts: 261
Its a semi float.
Thanks Joe! Appreciate the info!
Tracey
__________________
2005 Ford E-350 SMB 4x4
6.0 EB 50 floor plan. sold :(
TraceyAZ is offline   Reply With Quote
Old 10-31-2016, 03:04 PM   #4
Senior Member
 
JackTuppVan's Avatar
 
Join Date: Nov 2014
Location: TN
Posts: 299
TraceyAZ
The seal you mention is called the pinion seal.

I would first check the vent and make sure it is not blocked
(a blocked vent can cause pressure to build and result in oil being forced past the seals.)

To change the pinion seal you must remove the drive shaft ,pinion nut ,and pinion yoke .

Take note of the orientation of the yoke to the pinion shaft (reinstall the yoke in the same position as when you removed it.)

remove the pinion nut

Inspect the yoke where the seal rides for signs of wear.

Remove the pinion seal.

Clean the area where the seal rests.

Coat the rubber portion of the seal with grease.

Apply a small amount of black PERMATEX form-a-gasket on the metal portion of the seal where it contacts the diff. housing.

install the seal
install the yoke
install the pinion nut (torque to specs 250 ft-lbs ) use locktite
install the driveshaft

Step-By-Step Pinion Seal Replacement - Anti-Ooze
__________________
2007 E250 Super Duty cargo
1988 Toyota Van 4x4 5-spd
JackTuppVan is offline   Reply With Quote
Old 10-31-2016, 04:43 PM   #5
Senior Member
 
Join Date: Aug 2011
Posts: 261
Quote:
Originally Posted by JackTuppVan View Post
TraceyAZ
The seal you mention is called the pinion seal.

I would first check the vent and make sure it is not blocked
(a blocked vent can cause pressure to build and result in oil being forced past the seals.)

To change the pinion seal you must remove the drive shaft ,pinion nut ,and pinion yoke .

Take note of the orientation of the yoke to the pinion shaft (reinstall the yoke in the same position as when you removed it.)

remove the pinion nut

Inspect the yoke where the seal rides for signs of wear.

Remove the pinion seal.

Clean the area where the seal rests.

Coat the rubber portion of the seal with grease.

Apply a small amount of black PERMATEX form-a-gasket on the metal portion of the seal where it contacts the diff. housing.

install the seal
install the yoke
install the pinion nut (torque to specs 250 ft-lbs ) use locktite
install the driveshaft

Step-By-Step Pinion Seal Replacement - Anti-Ooze


Excellent! I was hoping it was gonna be just like the rear output seal on the transfer case, Just did that one last week! Just wasnt 100% and never hurts to ask questions! Thanks to Joe I was able to ID what rear diff I have, now its off to the dealership to get the parts! What sucks is I just did a fluid change on this a couple months ago....GRRR, no sign of it leaking then...LOL
Thank you Jack!
__________________
2005 Ford E-350 SMB 4x4
6.0 EB 50 floor plan. sold :(
TraceyAZ is offline   Reply With Quote
Old 10-31-2016, 05:07 PM   #6
Senior Member
 
Join Date: Jul 2011
Location: Flagstaff, AZ
Posts: 1,995
You can find those parts much cheaper online (RockAuto and the like) or at Napa than from the dealership. Axle seals and bearings and such were not made by Ford. They were made by Dana Spicer for Ford. The same D60 axle is found on Dodge and the like. One reason it's easy to get the wrong part #. Just say'n. And good stuff JackTupp!
__________________
2005 E350 RB 6.0 PSD for extended fun
1989 Landcruiser FJ62 for local fun
2011 VW TDI Golf for hwy fun
JoeH is offline   Reply With Quote
Old 11-03-2016, 08:04 PM   #7
Senior Member
 
Join Date: Aug 2011
Posts: 261
Quote:
Originally Posted by JackTuppVan View Post
TraceyAZ
The seal you mention is called the pinion seal.

I would first check the vent and make sure it is not blocked
(a blocked vent can cause pressure to build and result in oil being forced past the seals.)

To change the pinion seal you must remove the drive shaft ,pinion nut ,and pinion yoke .

Take note of the orientation of the yoke to the pinion shaft (reinstall the yoke in the same position as when you removed it.)

remove the pinion nut

Inspect the yoke where the seal rides for signs of wear.

Remove the pinion seal.

Clean the area where the seal rests.

Coat the rubber portion of the seal with grease.

Apply a small amount of black PERMATEX form-a-gasket on the metal portion of the seal where it contacts the diff. housing.

install the seal
install the yoke
install the pinion nut (torque to specs 250 ft-lbs ) use locktite
install the driveshaft

Step-By-Step Pinion Seal Replacement - Anti-Ooze

Any idea what size that pinion nut is? Not in my normal range of socket sizes!
Tracey
TraceyAZ is offline   Reply With Quote
Old 11-03-2016, 08:10 PM   #8
Senior Member
 
Join Date: Jul 2011
Location: Flagstaff, AZ
Posts: 1,995
Quote:
Originally Posted by TraceyAZ View Post
Any idea what size that pinion nut is? Not in my normal range of socket sizes!
Tracey
Could be wrong but I think 1 5/16. And an impact socket won't fit. Too thick.
__________________
2005 E350 RB 6.0 PSD for extended fun
1989 Landcruiser FJ62 for local fun
2011 VW TDI Golf for hwy fun
JoeH is offline   Reply With Quote
Old 11-03-2016, 08:34 PM   #9
Senior Member
 
Join Date: Aug 2011
Posts: 261
Quote:
Originally Posted by JoeH View Post
Could be wrong but I think 1 5/16. And an impact socket won't fit. Too thick.
That's what my caliper was telling me as well, just seemed like an oddball size, or I was doing it wrong. lol
Looks like a trip to the local tool cage.
Thanks Joe!
Tracey
TraceyAZ is offline   Reply With Quote
Old 11-03-2016, 08:42 PM   #10
Senior Member
 
JackTuppVan's Avatar
 
Join Date: Nov 2014
Location: TN
Posts: 299
Quote:
Originally Posted by JoeH View Post
Could be wrong but I think 1 5/16. And an impact socket won't fit. Too thick.
You're right It's 1 5/16 thin wall socket.

more detailed information here Best socket for D60 pinion nut? - Pirate4x4.Com : 4x4 and Off-Road Forum
__________________
2007 E250 Super Duty cargo
1988 Toyota Van 4x4 5-spd
JackTuppVan is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Sportsmobile SIP or any of its affiliates. This is an independent, unofficial site.


All times are GMT -6. The time now is 07:16 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.