|
|
04-09-2019, 08:54 AM
|
#1
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Help pop top install
Hey fellow friends,
I just sent off my doner van, the rusted out 89 e150 sportsmobile. I took all of my measurements, except the MOST IMPORTANT ONE! Can someone please help me out I need to know the measurement for the cut from the side to the hole and the rear to the hole. Can't figure out how to get this measurement to ensure that to fiberglass top sits properly in the gutter around the van.
Thanks In advance for any help you may be able to provide!
I posted in another section that I belive is the wrong section but it won't delete.
|
|
|
04-09-2019, 09:05 AM
|
#2
|
Senior Member
Join Date: May 2015
Location: San Clemente, CA
Posts: 552
|
My advice is to measure what you are putting in the hole. Obviously width wise have it centered on the van. For the lengthwise, all of the ones I have seen, the cut starts right behind the B pillar support, so then measure from there.
If your fiberglass is not attached to the lift mechanism, I actually placed my lift mechanism on the roof of my van and traced It.
I had measurements from a donor van, but felt this was easier and more foolproof.
|
|
|
04-09-2019, 09:35 AM
|
#3
|
Senior Member
Join Date: May 2017
Location: San Clemente, CA
Posts: 428
|
I had no measurements from my donor van and did exactly what bemerritt described above (he was there to help). Figure out the width of the lift mechanism and center that on the roof, then measure the length of the lift mechanism and start that cut right behind the B-pillar.
Good thing is, even if you are off a bit it doesn't really matter. If your lift mechanism is detached from the fiberglass roof you install the lift mechanism first and then position the roof on top of the crossbars so it sits right where you want it to. Then you attach the lift mechanism to the fiberglass roof. Hole can be off slightly and no one will ever know but you!
|
|
|
04-09-2019, 10:51 AM
|
#4
|
Senior Member
Join Date: Jul 2016
Location: Seattle, WA
Posts: 397
|
On my EB they took out one of the cross members and placed that behind the B pillar and started the cut from there backwards.
Rob
|
|
|
04-10-2019, 05:40 AM
|
#5
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Awesome yes I recall in the doner van it sitting right at the b pillar. The dinar van sold so fast I over looked those two measurements before it rolled away lol!
|
|
|
04-10-2019, 05:41 AM
|
#6
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Yea my lid is seperate, that was the biggest worry was the roof not lining up. Great point about being able to attach it where ever I need to worse case!
Ya'll wanna come help put another one on
|
|
|
04-10-2019, 05:42 AM
|
#7
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Nice, although that Would make it hard to determine where it actually started on my standard wb. Thanks for the reply!
|
|
|
04-11-2019, 01:15 PM
|
#8
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Adhesive
Maybe you guys can help! I was able to get 3/4 butyl for the sides. Although it looks like everything was 2" I'll just double it up. However on the front there is black butyl tape and over the mounting screws in the top. I can find this anywhere. I plan on putting my top on tomorrow. Can I use the grey butyl tape on the front? And can someone reccomend a sealant for the roof? I do an to replace the canvas later this year, I've hear some sealents make it impossible to get off. Your advise is greatly appreciated!
|
|
|
04-11-2019, 02:56 PM
|
#9
|
Senior Member
Join Date: May 2017
Location: San Clemente, CA
Posts: 428
|
Quote:
Originally Posted by Urbanoverlanding
Maybe you guys can help! I was able to get 3/4 butyl for the sides. Although it looks like everything was 2" I'll just double it up. However on the front there is black butyl tape and over the mounting screws in the top. I can find this anywhere. I plan on putting my top on tomorrow. Can I use the grey butyl tape on the front? And can someone reccomend a sealant for the roof? I do an to replace the canvas later this year, I've hear some sealents make it impossible to get off. Your advise is greatly appreciated!
|
I used 1 1/2" wide butyl all the way around attaching the canvas to the roof of the van. Layer of butyl, then the silicone gasket, then another layer of butyl, then screw the through the canvas, all 3 layers and the roof to hold it down. In the front where I attached over the channels in the van roof i just stacked butyl to fill the gaps.
https://www.mcmaster.com/76385a15
https://www.mcmaster.com/1142a78
Didn't use anything between the canvas and the fiberglass shell since it is not a sealing surface.
|
|
|
04-11-2019, 06:37 PM
|
#10
|
Junior Member
Join Date: Jul 2018
Posts: 23
|
Quote:
Originally Posted by BenJJ
I used 1 1/2" wide butyl all the way around attaching the canvas to the roof of the van. Layer of butyl, then the silicone gasket, then another layer of butyl, then screw the through the canvas, all 3 layers and the roof to hold it down. In the front where I attached over the channels in the van roof i just stacked butyl to fill the gaps.
https://www.mcmaster.com/76385a15
https://www.mcmaster.com/1142a78
Didn't use anything between the canvas and the fiberglass shell since it is not a sealing surface.
|
Do you not have the push boards? When I took mine apart there was a gap in the boards for what I assumed was the bars to be able to move when it goes up and down. But it looks like you just have a conduit clamp on there?
|
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|