|
|
11-27-2021, 01:17 PM
|
#1
|
Member
Join Date: Mar 2021
Location: Boulder, CO
Posts: 99
|
Replacing regulator in confined space
A month or so ago you all helped me diagnose a furnace issue. After pulling fixing and replacing the furnace it stopped working again when I needed it at 9800ft.
I determined that that regulator must be bad as that’s the last thing it could be and a service tech told me my regulator was bad when I had the water column pressure checked. I bought the regulator to replace myself. Trouble is, I can’t get the regulator off. So little room to work and fit tools I can’t get fittings to budge. I figured the rear line fitting was best to begin with because that would allow movement of the regulator from the fixed valve. But I actually don’t even see how I could unscrew/rotate the regulator with so little space even if I could get the rear line off which I can’t. So it appears the whole tank would need to be lowered and set off a series of other things that would need to be done to permit this. So. Any tricks or special tools that I am missing? Or is this an expensive pro service job for a otherwise simple regulator swap?
|
|
|
11-27-2021, 01:39 PM
|
#2
|
Senior Member
Join Date: Sep 2009
Location: SE Washington
Posts: 1,028
|
The discharge pipe/tubing will need to come off in any case. Since it's brass and copper it shouldn't freeze due to corrosion. It just needs the exact fitting wrenches and then torque.
If the regulator is wide enough to hit the tank when unscrewing, it is possible the pipes will flex enough to unscrew it anyhow.
__________________
---------------------
2009 E250 RB 5.4L "SilVan"
|
|
|
11-27-2021, 01:46 PM
|
#3
|
Member
Join Date: Mar 2021
Location: Boulder, CO
Posts: 99
|
What’s the discharge pipe/tubing? Is that the rearward fitting? Or something else?
|
|
|
11-27-2021, 01:52 PM
|
#4
|
Member
Join Date: Mar 2021
Location: Boulder, CO
Posts: 99
|
It seems to be loose (with some caulk like thread seal) at the regulator body thread (red line) but I can’t get the nut to loosen at the outer fitting to the exit line (blue circled nut)
|
|
|
11-27-2021, 04:50 PM
|
#5
|
Senior Member
Join Date: Nov 2019
Location: Denver Colorado
Posts: 820
|
Do you have one of these or a gas flare nut fitting wrench? They make all the difference.
https://www.google.com/aclk?sa=L&ai=...2sQvhd6BAgBEGc
__________________
2002 e350 window eb,
7.3
CCV high top
Conversion in process. Lol
Denver, CO
|
|
|
11-27-2021, 04:58 PM
|
#6
|
Senior Member
Join Date: Aug 2019
Location: Elk Grove, CA
Posts: 391
|
Before you go too far, I suggest you visit a full-service propane shop and get an estimate. I suspect they'll have the tools and expertise to do this without dropping the tank and it might not be too expensive. Even if they have to drop the tank the cost might not be as high as one might expect. There's no downside to asking.
The worst outcome would be for you to break something by trying to DIY it.
__________________
Bob
2005 E350 Super Duty Ext Wheelchair Van
2002 Itasca 35U Motorhome
|
|
|
11-27-2021, 06:29 PM
|
#7
|
Senior Member
Join Date: Jul 2013
Location: So Cal
Posts: 4,070
|
Is the hex nut in the lower right corner of the image part of the fitting that threads into the fill port? or can it spin independently of the fill port? If it can spin independently (spanner ring) you can loosen that and remove the whole assembly to work on it.......assuming there is a shut off valve beyond the fill port.
If this is confusing post another pic of the assembly from the other end/direction.
__________________
2008 E350 RB passenger 4WD SMB penthouse
2013 KTM 350 EXC
2008 KTM 250 XCF-W
2003 Honda Element
|
|
|
11-27-2021, 07:19 PM
|
#8
|
Senior Member
Join Date: Mar 2015
Location: Maryland
Posts: 3,378
|
Quote:
Originally Posted by boywonder
Is the hex nut in the lower right corner of the image part of the fitting that threads into the fill port? or can it spin independently of the fill port? If it can spin independently (spanner ring) you can loosen that and remove the whole assembly to work on it.......assuming there is a shut off valve beyond the fill port.
If this is confusing post another pic of the assembly from the other end/direction.
|
Believe you are correct on this boywonder, since none of components (regulator and the high pressure access fitting) can turn without being stopped by the proximity of the tank.
__________________
TwoXentrix
"AWOL"
|
|
|
11-27-2021, 07:57 PM
|
#9
|
Member
Join Date: Mar 2021
Location: Boulder, CO
Posts: 99
|
Quote:
Originally Posted by Twoxentrix
Believe you are correct on this boywonder, since none of components (regulator and the high pressure access fitting) can turn without being stopped by the proximity of the tank.
|
I will take a photo and post tomorrow just so I’m sure I follow. Thanks boywonder
|
|
|
11-28-2021, 02:40 PM
|
#10
|
Member
Join Date: Mar 2021
Location: Boulder, CO
Posts: 99
|
Thanks
Well shoot. Thanks all for the help. I found a tool I will never likely use again but it’s worth it’s weight in gold as it allowed me to grab those nuts in such a spot. It helped to give the WD40 24 hours to do its thing too.
Not sure if the new regulator will fix the furnace issues but at least that is done and I didn’t drop a pile of cash to do it. ✅
|
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
All times are GMT -6. The time now is 08:51 AM.