Forum: Hobbyist Vendor Products
08-20-2022, 07:25 PM
|
Replies: 13
Views: 6,629
|
Forum: 4x4
01-15-2021, 01:41 PM
|
Replies: 710
Views: 225,229
|
Forum: 4x4
01-15-2021, 12:57 PM
|
Replies: 710
Views: 225,229
Yeah. Since I didn't change rear axle I didn't...
Yeah. Since I didn't change rear axle I didn't adjust pinion angle via perches. Honestly, I didn't actually ever measure my pinion angle as I should have. I had seen another website or on facebook...
|
Forum: 4x4
01-14-2021, 07:04 PM
|
Replies: 710
Views: 225,229
Rear Shocks Fox 2.0 P/N 985-24-061 (2ea). This...
Rear Shocks Fox 2.0 P/N 985-24-061 (2ea). This what I used. The bottom attachment was a little too wide, so I trimmed them to fit. Maybe they fit w/ Sterling Axle, I dunno. I have a factory Dana...
|
Forum: 4x4
01-14-2021, 02:54 PM
|
Replies: 710
Views: 225,229
In rear, I used the Sky Offroad Design's 4.5"...
In rear, I used the Sky Offroad Design's 4.5" rear shackle flip & 1" extended Shackles (78-97 Truck/Bronco). Several guys have used this w/ good results. Also used 6 deg pinion shims from WFO to...
|
Forum: 4x4
01-14-2021, 08:48 AM
|
Replies: 710
Views: 225,229
|
Forum: Hobbyist Vendor Products
12-29-2020, 01:47 PM
|
Replies: 13
Views: 6,629
I think you can do that (i.e. remove oil tubes...
I think you can do that (i.e. remove oil tubes from cooler and use adapter to AN lines). I have two adapters for sale and would sell separate for $95 plus shipping (which is what I paid for them). ...
|
Forum: Hobbyist Vendor Products
12-10-2020, 08:28 AM
|
Replies: 13
Views: 6,629
|
Forum: Hobbyist Vendor Products
12-09-2020, 03:28 PM
|
Replies: 13
Views: 6,629
No apologies required, I could talk van's all...
No apologies required, I could talk van's all day. The Timberline adapter appears to be similar to the one Ujoint Offroad used to sell. No, the billet block isn't made to take hoses; its machined...
|
Forum: Hobbyist Vendor Products
12-09-2020, 01:37 PM
|
Replies: 13
Views: 6,629
|
Forum: Hobbyist Vendor Products
11-13-2020, 02:24 PM
|
Replies: 13
Views: 6,629
|
Forum: Hobbyist Vendor Products
08-28-2020, 09:02 AM
|
Replies: 13
Views: 6,629
6.0 Oil Filter Relocation
$180 - Ford Econoline 6.0 Powerstroke Oil Filter Relocation Hardware
-Machined oil filter adapter w/ orings
-2 AN fittings NPT to AN (-10 AN or JIC flare)
-2 90deg compression fittings
-Misc...
|
Forum: Testing
07-28-2020, 11:56 AM
|
Replies: 3
Views: 2,213
|
Forum: 4x4
07-27-2020, 07:03 PM
|
Replies: 710
Views: 225,229
6.0 oil filter options
Yeah. I'm apprehensive about the pushloc and will watch them closely. There are 2 grades of blue pushloc hose, and I ordered the slightly higher rated one. My goal was to use pushloc short term to...
|
Forum: 4x4
07-27-2020, 06:57 PM
|
Replies: 710
Views: 225,229
Front Crossmember Reinforcement
I had the same experience during cutting as above, piece of cake. If you cut clean, you could flip the cut scap portion and weld it to the backside of crossmember for extra support and it's free...
|
Forum: 4x4
07-22-2020, 08:19 PM
|
Replies: 710
Views: 225,229
6.0 oil filter options
I think the amsoil setup was just the typical dual spin on setup similar to others that required cutting oil tubes and using compression fittings to adapt to flex lines. Once you do this, you have...
|
Forum: 4x4
07-22-2020, 10:55 AM
|
Replies: 710
Views: 225,229
6.0 oil filter options
Any updates on what people are doing with this? I'm in the middle of moving my filter. I figure others must have had some good ideas or options.
|
Forum: Testing
07-22-2020, 10:14 AM
|
Replies: 3
Views: 2,213
|
Forum: Testing
07-22-2020, 10:13 AM
|
Replies: 3
Views: 2,213
|
Forum: 4x4
07-21-2020, 01:13 PM
|
Replies: 710
Views: 225,229
|